Cutting Schedules for High-Quality Alfalfa

Cut alfalfa earlier and more often, and quality goes up while tonnage and stand life take a hit. Cut it later and less often, and you stack up more tons of lower-quality, stemmy forage that a fresh cow will sort around. Every cutting schedule is a deal between those two, and the right one for your dairy depends on what the cows need and what the field can stand.
Alfalfa has opinions about the calendar, and it rarely agrees with the one hanging in the shop. A common starting point for high-quality dairy alfalfa in the northern states is a cut about every 28 to 35 days, depending on weather, growth stage and number of cuts the season allows. Treat that as a rough compass, not a law. The calendar matters less than the plant in front of you.
Yield versus quality in plain terms
As alfalfa matures, stems get thicker and more fibrous, and leaves make up a smaller share of the plant. Fiber gets harder for the cow to digest, and protein per pound drops. Yield, meanwhile, keeps climbing. That is why a late first cut looks great from the road and tests like fence post.
Dairy cows, especially high-producing ones, need digestible fiber and protein more than they need bulk. So dairy farmers usually harvest earlier than hay growers selling to horse owners. If you want to know what your forage is really worth, see how to sample forage for a lab analysis and then read the report using this guide to RFV, RFQ, NDF and beyond.
Common cutting systems
Standard schedule
Cut at roughly early flower, with the first cut a little earlier than the later ones. This gives a good balance for many farms and is easy on the stand. It often means three or four cuttings in the northern states, and more in longer seasons.
Early-cut or short interval
Cut at late bud to early bloom, often every 28 to 30 days. Quality is excellent, protein and digestibility are high, and you get an extra cutting in the season. The price is lower yield per cut and more stress on the stand. Stands under this system need good fertility, drainage and variety choice to keep going.
Long interval
Cut at full bloom or later. Yield is higher per cut but quality is lower, and old stems become a ration headache. This system fits cows with lower energy needs, such as far-off dry cows and heifers, more than a high-producing pen.
Southwest and irrigated regions
Where seasons are long and fields are irrigated, alfalfa may be cut many times a year on a tight interval, sometimes with distinct summer slumps in quality from heat. Schedules there depend on local water, heat and harvest labor, and the dairy forage specialists at your state university will have specific advice.
Reading the plant instead of the calendar
Maturity stage is the better guide. Look at the top third of the stand and watch for bud and flower development. Some farms use scissors-cut tools, which relate height to a quality estimate for a standing crop, while others rely on staging charts from their extension office. The University of Wisconsin alfalfa resources are a good place to find tools like these and region-specific advice.
A few practical cues:
- Buds visible, no flowers: quality is near its peak and the stand is ready for a good cut.
- Early bloom: a reasonable compromise between yield and quality.
- Lower leaves yellowing and dropping: you waited, and the leaf loss is already a protein loss.
- Regrowth buds at the crown: this is the plant telling you what the next cutting will look like. Cut before that regrowth gets long enough for the mower to clip it, which sets the next cutting back.
The fall cutting question
Fall is where well-meaning farmers hurt good stands. In regions with cold winters, alfalfa needs time to rebuild root reserves before dormancy. A cut taken too late in the season, with regrowth that gets caught by frost before it can store energy, can lead to winterkill the following spring.
The usual guidance in northern states is to either take the last cut early enough that the plant has several weeks of regrowth before a killing frost, or wait until after a killing frost to harvest. The window in between is the risky one. Exact timing differs by state and variety, so check with your extension forage specialist rather than going by a rule you heard at the co-op. In milder regions, such as the Southeast and the Southwest, fall dormancy is less of a concern, but plant health still depends on rest between cuts.
Weather, wilting and harvest timing
The best schedule on paper loses to a week of rain. Alfalfa dries slowly, and rained-on hay loses leaves, color and quality. This is where wilted haylage and wrapped bales earn their keep: they cut field time and allow earlier harvest on the schedule the plant sets rather than the one the forecast sets. If your system is bales, getting wrapping moisture and timing right keeps the quality you cut for. For the hay-only farm facing a soggy stretch, making dairy-quality hay in a wet summer covers what to do when the ground and the sky are both against you.
Mowing practices also count. Cut height influences regrowth speed, and a mower-conditioner speeds drying but can shatter leaves if the machine is set too aggressively. Tedding or raking too dry is a classic leaf-shattering move, and the leaves are where the protein lives. Rain on a cut field has a way of arriving the day after the tedder gets greased. If you want a good laugh, ask three neighbors how high to cut alfalfa and note how many correct answers you receive.
Matching the schedule to your herd
- High-producing, fresh and early-lactation cows: early-cut, top-quality alfalfa.
- Mid and late lactation: a mix of qualities works, saving the best for the high group.
- Dry cows and heifers: lower-quality, later-cut forage fits these groups. Over-conditioning a dry cow is easier than you think.
- Sold hay: buyers pay for what the test says, so follow what your market wants.
Keep each cutting separate and label it. Four cuttings at four qualities sitting in one pile is a waste of the work you put in. And if the stand itself is the question, start with whether alfalfa is worth growing on your dairy before you commit more acres.
Quick answers
How many days between alfalfa cuttings?
Roughly 28 to 40 days, depending on how much quality you want, how long the season is and how the stand is holding up. Shorter intervals give better quality and less yield per cut.
When should I make the last cut of the year?
In cold-winter regions, take it early enough for regrowth to rebuild root reserves before frost, or wait until after a killing frost. Ask your state extension forage specialist for the exact window in your area.
Does cutting alfalfa earlier hurt the stand?
It can shorten stand life if fertility, drainage and variety are not up to it. Frequent cutting works best on strong, well-managed stands and calls for good potassium and phosphorus levels.