Dairy Hub

Nutrition, Feed & Forage

Haylage Wrapping: Moisture, Layers and Timing

Mixer wagon feeding dairy cows

Good baleage comes down to three things: the forage goes in at the right moisture, the bale is dense, and the plastic goes on tight and fast. Miss any one of them and you have bought a very expensive white pumpkin that smells like a barn floor drain.

For most dairy forage, the sweet spot is wilted to roughly 40 to 60 percent dry matter, which is 40 to 60 percent moisture, then baled firm and wrapped within a few hours, and certainly the same day. Six layers of stretch film is the usual starting point for bales that will sit more than a few months. Everything else in this piece is detail around those three numbers.

Why moisture decides everything

Baleage is not hay with a raincoat. It is silage in a small package, and silage depends on fermentation. Bacteria inside the sealed bale eat the sugars and make acid, the pH drops, and the forage stabilizes. That only works inside a fairly narrow moisture window.

Too wet, and you get the wrong kind of fermentation. Clostridial bacteria move in, you get butyric acid, a sour smell that sticks to your gloves, and cows that turn their noses up at the bale. Too dry, and the bale does not ferment much at all, stays warm, and invites mold wherever a pinhole lets in air. Wetter forage also makes a heavier bale, which means more plastic per ton of dry matter and more diesel hauling water around.

Alfalfa and other legumes buffer acid, so they tend to need to go in a bit drier than grass or a grass mix. Many growers aim for the drier half of the range with straight alfalfa and the middle of it with grass. Your local extension forage specialist can tell you the window that fits your species and climate, and the University of Wisconsin forage production resources are a good place to start.

How to check moisture before you bale

  • Microwave or Koster tester. Slow, a little tedious, but accurate enough to settle an argument with your neighbor.
  • Handheld probe or moisture meter. Fast, handy, and good for trend-spotting. Check it against a real oven-dry sample now and then.
  • The squeeze test. Twist a handful hard. If juice drips, it is too wet. If it springs apart like crumpled paper, you are likely drier than you need to be. It is a sanity check, not a measurement.

Windrow moisture is not uniform. The top dries faster than the bottom, so sample from several spots and mix them. Merging two or three windrows into one can even things out and give the baler a thicker mat to work with.

Bale density and what the baler is doing

A loose bale holds air, and air is the enemy. Aim for a firm, dense bale made with the chamber as full as your baler allows. Variable-chamber and fixed-chamber balers both work, but they punish sloppy driving: if you weave and the bale comes out shaped like a barrel, the plastic will not seal around it cleanly.

Chopped forage, if your baler has a knife system, packs tighter and often ferments better and feeds easier. Net wrap beats twine for most baleage because it holds shape and gives the film something regular to cling to. Whichever you use, a bale that sags when it is lifted will sag worse in the field and develop wrinkles in the plastic.

Layers of wrap

Stretch film is made to cling, and the more layers, the less oxygen gets through. The common recommendation for individually wrapped bales is at least six layers, often applied as the wrapper makes a couple of passes with plenty of overlap. Four layers can work for forage you plan to feed within a couple of months, but it leaves less margin if a rodent or a bird gets curious.

Check the following when you wrap:

  1. Film should be stretched, not just wound on. Follow the manufacturer's stretch setting for your film.
  2. Overlap should be about half the film width on each pass so there are no thin spots.
  3. The ends of the bale should be covered as thoroughly as the barrel. That is where most pinholes appear.
  4. White film is common and keeps bales cooler in summer. Dark film warms up faster, which matters in the Southeast or Southwest where August sun can bake a bale sitting on a pallet.

Cheaper film is not always cheaper. Thin, poorly stretching film that tears in a crosswind can cost you more than the extra layer you were trying to save.

Timing: how fast to wrap

Oxygen is the clock. Once forage is baled, it keeps breathing and heating up until sealed. The rule of thumb is to wrap as soon as practical, preferably within a few hours, and not much later than the same day. A bale left in the field overnight loses sugars to respiration, heats up, and starts down a worse fermentation path.

Plan the day around the wrapper, not the other way around. A baler that outruns the wrapper leaves a row of naked bales sitting in the sun, getting quietly worse. Either run an inline wrapper, bring a second tractor and person, or slow the baler down. Rain on an unwrapped bale also pushes moisture up, so if the forecast turns, wrap first and argue with the weather later.

Handling after wrapping

Fresh-wrapped bales are tender. Move them gently with a bale squeeze or spear that does not poke holes, and stack or set them on their flat end if your system calls for it. Many farms prefer to leave them on a well-drained, gravel or sod pad and avoid parking them in tall weeds, where mice move in and chew through plastic. Give the bales some weeks to ferment before you open one for feeding. Six to eight weeks is a common rule of thumb.

Storage and troubleshooting

Walk your bale yard regularly. Patch small holes with a UV-rated tape made for the job; duct tape lasts about as long as a good intention. A bale that has been punctured and left will mold from the hole inward, and moldy forage is a feed-safety question, not just a smell problem. If you suspect mold or spoilage, see this guide to mycotoxins in dairy feed before the bale goes into the mixer.

A few common problems:

  • Sour, vinegary or rancid smell: probably too wet at baling, or wrapped too slowly.
  • Warm, moldy patches under the film: air got in, usually from a hole or too few layers.
  • Bales that tip or sag: too wet, too loose, or stacked on uneven ground.
  • Rodent damage: keep bale yards mowed and away from feed piles, and check often.

Baleage can work well beside bunker silage or bags, especially on smaller dairies that cannot justify an extra bunker for one cutting. If you are weighing it against chopped options, corn silage versus haylage covers how the two fit a ration, and round bales versus square bales helps with the equipment side. Test what you make. A lab analysis tells you what you actually put up, and sampling forage correctly keeps the test honest.

One last honest note: wrapped bales are not forgiving, and the plastic bill shows up whether the bale turns out well or not. The farms that do this consistently well are the ones that treat wrapping day like milking, same routine, same timing, no heroics.

Quick answers

What moisture should baleage be?

Most dairy baleage is baled at roughly 40 to 60 percent moisture, with legumes toward the drier end of that range. Check your own forage with a tester rather than guessing, because a few points matter.

How many layers of wrap does a bale need?

Six layers is the common recommendation for bales stored longer than a couple of months. Fewer layers can work for short storage, but they leave less protection against pinholes and oxygen.

How long can I wait to wrap after baling?

As soon as you can, ideally within a few hours. Waiting until the next day lets the bale heat and lose sugars, which hurts fermentation and feed quality.

More from farm.FM Need a break from the paperwork? Farm humor and funny farm stories are always in season at farm.FM.