Dairy Hub

Nutrition, Feed & Forage

How to Spot and Stop Silage Heating at the Face

Mixer wagon feeding dairy cows

If you put your hand a foot into the face and it comes out warm, the silage is already burning feed. Heating at the face means air got in, yeast and mold woke up, and sugars that should have become milk are turning into carbon dioxide, water and heat. The fix has two parts: remove the face faster than the heat can spread, and figure out why oxygen was there to begin with.

Warm silage is a quiet loss. It does not look dramatic, the cows keep eating it, and the milk check slips a little. Then the TMR sorts, intake drops and someone blames the mineral. Usually it was the pile.

What is actually happening

Silage stays stable as long as acids from fermentation keep spoilage organisms in check, and oxygen stays low. Once you open the face, air moves into the pile. Yeasts that tolerate acid use the lactic acid as food, which raises pH and generates heat. After that, molds and other microbes move in. Dense silage resists this longer because air has farther to travel, and a tight face can hold for days. A loose one starts warming overnight.

Corn silage tends to carry more fermentable sugar and starch, and it is generally more prone to heating at the face than many hay silages. Wetter forage and drier forage both have trouble in different ways, and the harvest-day basics in timing corn silage by moisture influence stability months later.

How to spot it

By sight and smell

  • Steam rising from the face on cool mornings.
  • White or gray mold, or visible patches of discolored silage.
  • A sharp, vinegar or alcohol smell, or a musty, compost-pile odor.
  • Dark, slimy or crumbly areas that look cooked.

By temperature

Push a long probe thermometer into the face at several spots and a couple of feet deep. Compare the readings to the ambient air temperature and to silage deeper in the pile. A sustained difference of several degrees warmer than the surrounding feed is a warning, and large differences point to active spoilage. Take readings at the same times each day to see trends. Some farms use infrared thermometers or cameras for quick scans, though they only read the surface.

By the herd

Drops in dry matter intake, more sorting, loose manure or lower milk can be signs that cows are rejecting or reacting to spoiled feed. Spoiled silage may also carry molds that produce toxins. Read about mycotoxins in dairy feed and talk with your veterinarian and nutritionist if you see herd-level changes.

Set a feedout rate that stays ahead

The face should move forward faster than spoilage can follow it. Typical advice from extension programs is to remove several inches a day in cold weather and a foot or more in warm weather, and the exact number depends on silage density, temperature and quality. A face that is too wide for the herd is the usual culprit. You can fix that with a narrower face, which means a smaller bunker, a dividing wall or a different storage setup.

A quick check: measure the width and height of the face, estimate the weight per cubic foot from your density number, and see how much silage the herd uses per day. Then compare it to how much you need to remove to keep the face moving. If the numbers do not meet, no amount of scolding at the feed pusher will help. Planning your forage inventory includes this daily draw.

How to cut the face properly

  1. Use the right tool. A defacer, shear grab or block cutter leaves a smooth, tight face. A bucket that rips and tears loosens silage back into the pile.
  2. Keep the face vertical and flat. Overhanging lips and pockets let air in. Silage that falls on its own is dangerous as well as wasteful.
  3. Take it the full width and height. Do not pick at the bottom or dig tunnels.
  4. Pull only what you will feed. Do not pile loose silage in front of the face and leave it, because it heats quickly.
  5. Keep the plastic tight to the face. Roll the cover back only as far as you need, and secure it again so wind and rain do not pump air in behind it.

Never stand beneath an overhanging face or climb on the pile while the face is being cut. Silage collapses without warning, so keep people and equipment back from the edge.

What to do with heated silage

Do not feed spoiled or moldy material. Remove visibly heated, moldy or slimy silage and discard it away from cattle, and avoid mixing it into the TMR to dilute it. Cows can be sensitive to mold, and toxins can affect health, fertility and milk. If you are unsure how much is affected, your nutritionist or veterinarian can help you decide what to discard and what testing makes sense. When the face looks bad, handling refusals and leftover feed covers where the rejected material should go.

Warm silage that is still sound is not a cause for panic, but it is a cue to speed up removal and fix whatever let air in.

Fix the root causes

  • Density. Thin layers, heavy tractors and enough packing time at harvest. The routine is in packing a bunker the right way.
  • Sealing. Oxygen barrier film, overlapped plastic, and covers weighted along the edges.
  • Face size. A smaller face for the herd means faster daily movement.
  • Moisture and chop length. Drier silage with long chop packs poorly and heats sooner.
  • Additives. Some bacterial inoculants are designed to improve aerobic stability. Read whether silage inoculants pay for themselves before spending money on them.

Warm weather makes everything worse. In the Southeast and the Southwest, summer feedout means every day counts. In the Upper Midwest and Northeast, a cold face can hide trouble until the first warm spell, then everything wakes up at once, like a teenager on a Saturday.

The University of Wisconsin's forage and silage hub has research summaries on silage storage and stability.

Quick answers

How warm is too warm for a silage face?

Compare the face to ambient air and to cooler silage deeper in the pile. A sustained rise of a few degrees is a sign of trouble, and a face much warmer than the surrounding air points to active spoilage that needs a faster feedout.

Can I feed silage that is only slightly warm?

If it looks, smells and tests normal, many herds do. Watch cow intake and consult your nutritionist. Remove anything moldy, slimy or sour-smelling before it reaches the mixer.

How fast should I remove silage from the face?

Typically a few inches a day in cold weather and a foot or more in hot weather. If your herd cannot keep up, consider a narrower face or a different storage setup.

More from farm.FM Need a break from the paperwork? Farm humor and funny farm stories are always in season at farm.FM.