Dairy Hub

Barns, Cow Comfort & Equipment

Buying Used Dairy Equipment: What to Check

Holstein cow in a robotic milking stall

Used dairy equipment can save real money, and it can also turn into the most expensive free stuff you ever hauled home. The difference is almost always inspection. Look at what touches the milk first, what keeps the milk cold second, and what moves cows or manure last. Then ask what it would take to get the whole thing past your milk inspector.

Auctions are the hardest place to be disciplined. The gavel is quick, the pickup is already hooked up, and everyone in the lot has an opinion about a stainless steel tank that you cannot check until it is yours. Go early, bring a flashlight and a notebook, and decide your limit before the bidding starts. Auctioneers are friendly people, but they are not responsible for your bulk tank.

Start with the rules, not the equipment

Before you fall in love with a tank, find out what your milk buyer and state dairy regulator require. Grade A milk is regulated under state programs that follow federal guidance, and what the inspector expects for stainless surfaces, cleanability, cooling and pipeline layout can affect whether used gear is acceptable at all. Details vary by state and by milk handler, so call your field rep and your state dairy agency before you buy. The USDA Agricultural Marketing Service and your state agriculture department are the places to start for official information.

If you are building a bottling or cheese operation, equipment that was fine for a bulk-tank dairy may not meet plant rules. Check first, buy second.

The bulk tank

The bulk tank is the most important piece of used equipment to inspect, because it is both a food-contact surface and your cooling system. Ask these questions.

  • Inside surface. Look for pitting, deep scratches, dents or rough welds. Milk residue loves a scratch. If you can see a rough spot, a cleaning brush will have a hard time with it.
  • Cooling performance. Ask for a cooling record or run it. A tank that does not cool a load quickly enough will cost you in bacteria counts and possibly in rejected milk.
  • Compressor and condenser. Listen for noise, check for oil leaks and see whether the condenser is clean and undamaged. A good refrigeration technician can tell you what is left in the unit.
  • Agitator, outlet valve and gaskets. Gaskets are cheap. A valve that will not seal is not.
  • Calibration. A tank needs a calibration chart and measuring stick that match the tank. A stick from another tank gives you wrong numbers on your milk check.
  • Size. Match capacity to your herd and pickup schedule. A tank that is too small will get you in a bind between hauls.

Why the tank matters so much to your income is covered in the milk hauler pickup schedule and access guide: capacity and pickup interval work together.

Milking units, pulsators and vacuum

The parts that go on the cow need the most care. Look at claws, shells, hoses and pulsators, and remember that liners and rubber hoses wear out and should be replaced, no matter what the seller says about "just changed them." Plan on new rubber parts as a cost of buying used.

For the vacuum system, listen to the pump, check the oil and belts, and look at the regulator and vacuum lines. Lines that are crushed, cracked or full of old water make poor vacuum. Ask whether the system was ever tested by a qualified technician. The best step is to have a technician run a full test after you install it, and your milking machine maintenance schedule should start on day one. A used system that was fine in the other barn may not be fine in yours, because pipe lengths, stall numbers and pump size all change.

Used parlor gear

Parlor hardware, such as stall dividers, arm-and-gate systems, cow identification, milk meters and detachers, should be checked for wear, corrosion and missing parts. Ask whether parts are still available. An old model with no available repair parts is not a bargain, it is a lawn ornament. If you are weighing layouts, picking a parlor first will tell you what to look for.

Wash system, water and plate coolers

Cleaning equipment makes or breaks milk quality. Check wash sinks, wash lines, pumps, timers and any automated wash unit for leaks and worn components. Make sure your hot water heater can supply the volume and temperature that the wash routine needs; see wash water temperature and chemicals for how that fits together. Plate coolers should be checked for leaks and cross-contamination risk, since a pinhole in the wrong spot lets water into a milk path. If a plate cooler cannot be proven sound, replace it.

Feed, manure and barn equipment

Not everything needs a technician, but most of it needs a close look.

  • TMR mixers. Check augers, knives, bearings, gearbox oil leaks, scale heads and load cells. Worn knives mean poor mixing and ugly particle size. A mixer that cannot weigh accurately costs you every day.
  • Skid steers, loaders and feed pushers. Hours, hydraulic leaks, tire condition and frame cracks. Ask for service records.
  • Scrapers and manure equipment. Cables, chains, corners, drives and blades. Manure is hard on everything it touches.
  • Fans, curtains and controllers. Motors, bearings, blade condition and guards. Missing guards are a safety issue.
  • Gates, headlocks and stalls. Bends, cracks and rust at welds. A bent neck rail changes how a cow lies down.

A simple used-equipment checklist

  1. Confirm with your milk buyer and state regulator that the item is acceptable.
  2. Ask for service records, model and serial numbers, and the seller's reason for selling.
  3. Inspect it with a technician or an experienced neighbor, preferably running.
  4. Price the repairs and rubber parts into your top bid.
  5. Confirm availability of parts and a local service tech.
  6. Get everything in writing, including "sold as is" terms and who pays for hauling.
  7. Confirm the electrical, plumbing and space needs at your barn before it gets there.

Compare the real total, including hauling, installation and the inevitable extra part, to the cost of new or leased gear. The used dairy equipment buying checklist from the finance side and leasing versus buying help you decide whether the discount is a bargain or just a smaller bill for a larger headache.

Common mistakes

  • Bidding on a tank you could not look inside.
  • Forgetting that the old barn had different pipe lengths and electrical service.
  • Assuming parts are interchangeable between brands and models.
  • Skipping a qualified test after installation.
  • Falling in love with a price instead of a result.

Quick answers

Is a used bulk tank okay to buy?

Often, yes, if the inside surface is smooth, the cooling is proven and it meets what your buyer and state inspector expect. A tank with deep pitting or a tired compressor can cost more than it saves.

Should I replace milking rubber on used equipment?

Plan on it. Liners and hoses wear out, and replacing them at purchase is cheap insurance for udder health and milk quality. Your dealer can tell you the right parts for your units.

Who should inspect equipment before I buy?

A milking equipment dealer or independent technician for milking and cooling gear, and a mechanic you trust for engines and hydraulics. Your milk buyer's field rep can tell you what will pass.

More from farm.FM Need a break from the paperwork? Farm humor and funny farm stories are always in season at farm.FM.