Barns, Cow Comfort & Equipment
Freestall Neck Rail and Brisket Locator Placement

If your cows are lying with their heads under a rail, or standing with their front feet on the bed and their back feet in the alley, look at the steel before you blame the cows. The neck rail and brisket locator are two pieces of pipe that decide how a cow positions herself, and an inch or two in the wrong direction can make a stall feel like a bad bus seat.
The rule of thumb: the neck rail should be set so the largest cow stands with her back level and the top of her neck just brushing the rail, and the brisket locator should be low enough that she can swing her head forward and step ahead without catching her chest. Set both for the biggest cows in the pen and the rest will adapt.
What each piece does
The neck rail is a horizontal pipe running above the stall, usually a bit forward of the middle of the bed. Its job is to keep a standing cow from moving too far forward, so her back end stays near the rear curb and her manure lands in the alley, not the bed. Think of it as a polite reminder that this is a bed and not a hallway.
The brisket locator (some call it a brisket board or brisket rail) is a low rail or board at the front of the stall. It keeps a cow from lying too far forward and gives her something to brace against when she rises.
Neck rail height
Neck rail height is measured above the stall bed (or curb surface, depending on the table you are reading, so check which). For a 1,300 to 1,500 pound cow, Penn State Extension gives a range of about 46 to 48 inches, stepping up for larger cows. Smaller Holsteins and Jerseys come in a few inches lower, and the biggest animals a few inches higher. You can read the full table on the Penn State dairy freestall design page.
The cleaner way to check it is on the cow. Stand your biggest cow in the stall with her legs under her and her back level. The rail should touch the upper part of her neck gently. If she has to arch her back to stay off the rail, it is too low. If she can walk forward and stand with her shoulders over the bed, it is too high.
Neck rail distance from the rear curb
This is the number most people get wrong, and it matters more than height. Measured back from the rear curb, the neck rail typically sits in the mid-60-inch range for a mature Holstein. Mattress stalls usually put it a few inches farther forward than deep-bedded sand stalls, because a cow in a deep bed tends to keep her rear feet back in the alley and the shorter distance encourages that.
Too close to the curb, and a cow cannot lie straight. She will lie diagonally to get her head out from under the rail, which means her hips end up out of position and the bed gets soiled unevenly. Too far forward, and the rail stops doing its job and you have a cow standing wherever she likes. Perching, the habit of standing with only the front feet in the stall, shows up in both cases for different reasons, and why cows stand half in, half out of stalls covers how to tell which one you have.
Brisket locator height and position
Keep the brisket locator low. Recommendations vary slightly between universities, but they cluster around 4 inches or less above the bed surface, with some tables allowing up to 6. A cow rising needs to lunge forward, and a tall brisket board is something she has to climb over while her weight is on her knees. That is the reason cows that rise slowly, or that stop halfway up, are sometimes sitting in a stall with a locator that is a little too proud.
Position matters as well. If the locator is too close to the rear curb, it shortens the lying space and cows end up with their legs hanging off the back. The published tables put the locator roughly 64 to 72 inches from the rear curb depending on cow size, so it tracks stall length, which is why sizing freestalls for your cows comes first.
Adjusting what you have
You do not need to tear out a row of stalls to fix this. Most freestall neck rails are mounted on adjustable brackets or can be re-drilled, and brisket locators are often just a board or a pipe at a fixed height that you can lower. A good plan:
- Pick one pen and fix a handful of stalls first. Mark them so you can compare use.
- Measure the current rail height and distance from the rear curb. Write them down. You will forget otherwise.
- Check the largest cows. If they are fitting, the smaller cows will be fine.
- Move the neck rail in small steps, not big ones. An inch can change how a cow stands.
- Lower the brisket locator if it sits above about 4 inches, and check that it is not blocking the lunge path.
- Watch the pen at night and count how many stalls are in use. Cows vote with their legs.
Give changes a few days before judging them. Cows are creatures of habit, and a stall they have learned to hate will take a week or two to forgive.
Mistakes to avoid
- Setting rail height for the average cow and leaving the big cows to deal with it.
- Moving the neck rail without checking the lunge path and divider loops.
- Installing a high brisket board because the contractor already had one.
- Ignoring the bed itself. A thin, packed bed makes cows move around no matter how perfect the steel is. For mattress stalls, the options in choosing stall mattresses for dairy cows affect how much bedding you need on top.
- Skipping the walk-through. An hour of watching beats a day of measuring, and the one-hour cow comfort walk-through shows you how.
When the fix is cheap
This is one of the best bangs for the buck in a dairy barn, and it often costs a few hours of labor and some bolts. Seven barn fixes that cost less than a vet call has more in this category, since a lot of cow-comfort problems turn out to be a piece of pipe in the wrong spot.
If you are building new, ask the supplier for the dimensions in writing for your cow size, and compare them against a land-grant extension table. The supplier's standard stall may have been drawn for a smaller herd than yours.
Quick answers
How high should a freestall neck rail be?
For mature Holsteins in the 1,300 to 1,500 pound range, a typical range is about 46 to 48 inches above the stall surface, higher for bigger cows and lower for Jerseys. Test it on your largest cow: it should lightly touch her neck when she stands with a level back.
How high should the brisket locator be?
Generally about 4 inches or less above the bed, with some tables allowing up to 6. Lower is safer for rising, since a tall board gets in the way of the forward lunge.
Why do cows lie diagonally in my stalls?
The most common causes are a neck rail too close to the rear curb, a locator too high, or something blocking the front of the stall. Check those before anything else, and make sure stalls are wide enough for your biggest cows.